Baymak Jetinox 112-20LT Horizontal Tank Booster Pump, 6 Floors, 6 Apartments
$449.95 $599.94 · In stock
Brand: Baymak · SKU: JETINOX112-20LT-02030079 · Warranty: 24 months
Other options
- Baymak Jet 82-20LT Booster Pump, Horizontal Tank, 3 Floors, 4 Apartments – $374.59
- Baymak Jetinox 82-20LT Stainless Steel Horizontal Tank Booster Pump, 3 Floors, 4 Apartments – $426.34
- Baymak Jet 82-50LT Booster Pump, Horizontal Tank, 3 Floors, 4 Units – $500.15
- Baymak Jetinox 82-50LT Stainless Steel Horizontal-Tank Booster Pump, 3 Floors, 4 Units – $537.88
- Baymak Jet 102-20LT Booster Pump with Horizontal Tank, 4 Floors, 5 Units – $401.39
- Baymak Jetinox 102-20LT Stainless Steel Horizontal-Tank Booster Pump, 4-Floor 5-Apartment – $438.02
- Baymak Jet 102-50LT Horizontal Tank Booster Pump, 4 Floors, 5 Apartments – $533.60
- Baymak Jetinox 102-50LT Booster Pump, Stainless Steel Casing, Horizontal Tank, 4 Floors, 5 Units (out of stock)
- Baymak Jet 112-20LT Horizontal-Tank Booster Pump, 6 Floors, 6 Apartments – $486.15
- Baymak Jet 112-50LT Horizontal Tank Booster Pump, 6 Floors, 6 Apartments (out of stock)
- Baymak Jetinox 112-50LT Booster Pump, Horizontal Tank, 6 Floors, 6 Apartments (out of stock)
- Baymak Jet 151-50LT Horizontal Tank Booster Pump, 6 Floors, 12 Apartments – $877.94
- Baymak Jet 251-50LT Booster Pump, Horizontal Tank, 6 Floors, 18 Units (out of stock)
Product description
Covered by a 2-year Baymak warranty.
You must request a free commissioning service from Baymak to activate the warranty.
Baymak Jetinox 112-20LT Horizontal Tank Booster Pump Specifications
- An original DAB pump is used. It has a stainless steel casing. It is shipped ready-assembled in its packaging.
- Can draw water from depths of up to 8 m. (Capacity varies depending on suction depth.)
- The flexible pipe is short, so it takes up less space.
- Rust-proof due to the tank not being in contact with water and having an oven-painted finish.
- Shipped with a 1-meter plug-in cable.
Baymak Jetinox 112-20LT Technical Specifications
- Mechanical Seal: Carbon / Ceramic / NBR
- Impeller Material: Technopolymer
- Pump Casing: Stainless Steel
- Pump Shaft: Stainless Steel
- Venturi, Diffuser: Technopolymer
- Protection Class: IP 44
- Insulation Class: F
- Max. Fluid Temperature: +40 °C
- Max. Operating Pressure Rating: 8 Bar
- Operating Pressure Range: 3.5–5 Bar
- Connection Size: 1" / 1"
- Motor Power: 1.5 HP / 1.1 kW
- Total Weight: 21 kg
- Voltage: 220 V
| A(mm) | B(mm) | C(mm) | D(mm) | E(mm) | F(mm) | H(mm) |
| 560 | 270 | 425 | 510 | 250 | 245 | 250 |
Baymak Jetinox 112-20LT Important Notes
- Baymak booster pump initial start-up must be carried out by an authorized Baymak service technician. Otherwise, the warranty will be void.
- Transport the Baymak Jetinox 112-20LT only in its original packaging, following all warnings printed on the box.
- For installation of the Baymak Jetinox 112-20LT, it is recommended to draw suction at least 30 cm above the bottom of the tank to prevent foreign matter in the water (sand, etc.) from damaging the unit.
- The Baymak booster pump must not be connected to draw directly from the city mains; it must draw from a storage tank.
- Do not tamper with the expansion vessel air valve; it should be filled with pressurized air only when the pump contains no water.
- The pressure switch has been factory-set and should not be adjusted.
- Baymak booster pump, it is recommended to install it in a well-ventilated location where the temperature does not exceed 40°C.
- Install the suction and discharge pipes with clamps so that the load is transferred to the wall.
- If the Baymak Jetinox 112-20LT fails to start after a period of inactivity, loosen the shaft at the rear of the motor.
- If the water inside the unit is to be completely drained, this must be done in an environment below 0 °C. If the unit will not be used for an extended period, draining is recommended to prevent internal corrosion.
- Fit a switch proportional to the current, following the information on the Baymak Jetinox 112-20LT nameplate.
- Under no circumstances allow anyone other than authorized service personnel to work on the unit.
- For the installation piping: if metal pipe is used, the inlet/outlet diameters must be the same; if plastic pipe is used, the next size up should be selected.
- The suction line should be as short as possible (maximum 6 m) and made with the fewest possible fittings.
- Never run the Baymak Jetinox 112-20LT dry. Otherwise the mechanical seal, impeller, and electric motor will burn out and the warranty will be void.
- We recommend using the Baymak Jetinox 112-20LT with a protection panel to guard against electrical faults.
Specifications
| Brand | Baymak |
|---|
Similar products
- Water Sound GP2624 Automatic Booster Pump, 24V, 120W, Caravan & Boat – $224.50
- Water Sound GP2612 Automatic Booster Pump, 12V, 120W, Caravan & Boat – $224.50
- Hidrotank TD 50 Vertical Pressure Tank, 50 L, 1″ Connection – $96.15
- İKRAHİDRO-11H 1 Floor 1 Apartment Booster Pump with Pressure Switch – $106.98
- Seaflo Automatic Booster Pump, 12V, 24 L Tank, Boat, Yacht & Caravan – $302.45
- Cacheng Low-Noise Automatic Mains Pressure Booster Pump, 42 L/min, 3 Bar – $250.94
- Low-Noise Booster Pump, 24V, Boat, Yacht & Caravan, 25 L/min, 2 Bar – $126.76
- Hidrotank Globe Booster Pump Kit with Connection Set, 24 L – $106.98
- Forza TGP 130 Automatic Water Booster Pump, 3.5 Bar – $83.31
- Nano Water Filter, 1 Inch – $171.69