Baymak Jet 82-20LT Booster Pump, Horizontal Tank, 3 Floors, 4 Apartments
$374.59 $499.46 · In stock
Brand: Baymak · SKU: JET82-20LT-01050050 · Warranty: 24 months
Other options
- Baymak Jetinox 82-20LT Stainless Steel Horizontal Tank Booster Pump, 3 Floors, 4 Apartments – $426.34
- Baymak Jet 82-50LT Booster Pump, Horizontal Tank, 3 Floors, 4 Units – $500.15
- Baymak Jetinox 82-50LT Stainless Steel Horizontal-Tank Booster Pump, 3 Floors, 4 Units – $537.88
- Baymak Jet 102-20LT Booster Pump with Horizontal Tank, 4 Floors, 5 Units – $401.39
- Baymak Jetinox 102-20LT Stainless Steel Horizontal-Tank Booster Pump, 4-Floor 5-Apartment – $438.02
- Baymak Jet 102-50LT Horizontal Tank Booster Pump, 4 Floors, 5 Apartments – $533.60
- Baymak Jetinox 102-50LT Booster Pump, Stainless Steel Casing, Horizontal Tank, 4 Floors, 5 Units (out of stock)
- Baymak Jet 112-20LT Horizontal-Tank Booster Pump, 6 Floors, 6 Apartments – $486.15
- Baymak Jetinox 112-20LT Horizontal Tank Booster Pump, 6 Floors, 6 Apartments – $449.95
- Baymak Jet 112-50LT Horizontal Tank Booster Pump, 6 Floors, 6 Apartments (out of stock)
- Baymak Jetinox 112-50LT Booster Pump, Horizontal Tank, 6 Floors, 6 Apartments (out of stock)
- Baymak Jet 151-50LT Horizontal Tank Booster Pump, 6 Floors, 12 Apartments – $877.94
- Baymak Jet 251-50LT Booster Pump, Horizontal Tank, 6 Floors, 18 Units (out of stock)
Product description
Covered by a 2-year Baymak warranty.
To start the warranty, a commissioning request must be submitted to Baymak.
Baymak Jet 82-20LT Horizontal Tank Booster Pump Specifications
- The Baymak Jet 82 m booster pump with a 20 L tank is an original DAB cast iron unit. It is shipped ready as a complete package.
- The Jet 82 booster pump can draw water from a depth of up to 8 meters. (Capacity varies depending on suction depth.)
- The Baymak booster pump Jet 82 flexible hose is short, so it takes up little space.
- The tank does not rust because it does not come into contact with water and has an oven-painted finish.
- Shipped with a 1-meter plug-in cable.
- A float switch is included, connected to the unit.
Baymak Jet 82-20LT Technical Specifications
- Mechanical Seal: Carbon / Ceramic / NBR
- Impeller Material: Technopolymer
- Pump Casing: Cast Iron
- Pump Shaft: Stainless Steel
- Venturi, Diffuser: Technopolymer
- Protection Class: IP 44
- Insulation Class: F
- Max. Fluid Temperature: +40 °C
- Max. Operating Pressure Rating: 8 Bar
- Operating Pressure Range: 2–3.5 Bar
- Connection Size: 1" / 1"
- Motor Power: 0.8 HP / 0.60 kW
- Total Weight: 21 kg
- Voltage: 220 V
| A(mm) | B(mm) | C(mm) | D(mm) | E(mm) | F(mm) | H(mm) |
| 560 | 290 | 425 | 510 | 250 | 245 | 560 |
Baymak Jet 82-20LT Important Notes
- Baymak booster pump initial start-up must be carried out by an authorized Baymak service center. Otherwise, the warranty will be void.
- For shipping the Baymak Jet 82-20LT, use only its original packaging, observing the warnings on the box.
- For installation of the Baymak Jet 82-20LT, it is recommended to draw water at least 30 cm above the tank floor to prevent foreign matter in the water (sand, etc.) from damaging the product.
- The Baymak booster pump must not be connected to draw directly from the city mains; it must draw from a storage tank.
- Do not interfere with the expansion vessel valve; it is charged with compressed air when there is no water in the pump.
- The pressure switch has been factory-set; do not make any adjustments.
- It is recommended to install the Baymak booster pump in a well-ventilated location where the temperature does not exceed 40 °C.
- Install the suction and discharge pipes with clamps so that the load is transferred to the wall.
- If the Baymak Jet 82-20LT does not move after being idle for a period, loosen the shaft at the rear of the motor.
- If the water inside the unit is to be completely drained, this must be done in an environment below 0 °C. If the unit will not be used for an extended period, draining is recommended to prevent internal corrosion.
- Refer to the information on the Baymak Jet 82-20LT label and install a switch proportional to the current.
- Under no circumstances allow anyone other than authorized service personnel to work on the unit.
- For the installation piping: if metal pipe is used, the inlet/outlet diameters must be the same; if plastic pipe is used, the next size up should be selected.
- The suction line should be as short as possible (maximum 6 m) and made with the fewest possible fittings.
- Never run the Baymak Jet 82-20LT dry. Otherwise the mechanical seal, impeller, and electric motor will burn out and the warranty will be void.
- We recommend using the Baymak Jet 82-20LT with a protection panel against electrical faults.
Specifications
| Brand | Baymak |
|---|
Similar products
- Water Sound GP2624 Automatic Booster Pump, 24V, 120W, Caravan & Boat – $224.50
- Water Sound GP2612 Automatic Booster Pump, 12V, 120W, Caravan & Boat – $224.50
- Hidrotank TD 50 Vertical Pressure Tank, 50 L, 1″ Connection – $96.15
- İKRAHİDRO-11H 1 Floor 1 Apartment Booster Pump with Pressure Switch – $106.98
- Seaflo Automatic Booster Pump, 12V, 24 L Tank, Boat, Yacht & Caravan – $302.45
- Cacheng Low-Noise Automatic Mains Pressure Booster Pump, 42 L/min, 3 Bar – $250.94
- Low-Noise Booster Pump, 24V, Boat, Yacht & Caravan, 25 L/min, 2 Bar – $126.76
- Hidrotank Globe Booster Pump Kit with Connection Set, 24 L – $106.98
- Forza TGP 130 Automatic Water Booster Pump, 3.5 Bar – $83.31
- Nano Water Filter, 1 Inch – $171.69