Baymak Jet 82-50LT Booster Pump, Horizontal Tank, 3 Floors, 4 Units
$500.15 $666.87 · In stock
Brand: Baymak · SKU: JET82-50LT-1050052 · Warranty: 24 months
Other options
- Baymak Jet 82-20LT Booster Pump, Horizontal Tank, 3 Floors, 4 Apartments – $374.59
- Baymak Jetinox 82-20LT Stainless Steel Horizontal Tank Booster Pump, 3 Floors, 4 Apartments – $426.34
- Baymak Jetinox 82-50LT Stainless Steel Horizontal-Tank Booster Pump, 3 Floors, 4 Units – $537.88
- Baymak Jet 102-20LT Booster Pump with Horizontal Tank, 4 Floors, 5 Units – $401.39
- Baymak Jetinox 102-20LT Stainless Steel Horizontal-Tank Booster Pump, 4-Floor 5-Apartment – $438.02
- Baymak Jet 102-50LT Horizontal Tank Booster Pump, 4 Floors, 5 Apartments – $533.60
- Baymak Jetinox 102-50LT Booster Pump, Stainless Steel Casing, Horizontal Tank, 4 Floors, 5 Units (out of stock)
- Baymak Jet 112-20LT Horizontal-Tank Booster Pump, 6 Floors, 6 Apartments – $486.15
- Baymak Jetinox 112-20LT Horizontal Tank Booster Pump, 6 Floors, 6 Apartments – $449.95
- Baymak Jet 112-50LT Horizontal Tank Booster Pump, 6 Floors, 6 Apartments (out of stock)
- Baymak Jetinox 112-50LT Booster Pump, Horizontal Tank, 6 Floors, 6 Apartments (out of stock)
- Baymak Jet 151-50LT Horizontal Tank Booster Pump, 6 Floors, 12 Apartments – $877.94
- Baymak Jet 251-50LT Booster Pump, Horizontal Tank, 6 Floors, 18 Units (out of stock)
Product description
Covered by a 2-year Baymak warranty.
For warranty purposes, you must request free commissioning from Baymak.
Baymak Jet 82-50LT Horizontal Tank Booster Pump Specifications
- The original DAB is cast iron. It is shipped ready in its packaging.
- Can draw suction from depths of up to 8 meters. (Capacity varies depending on suction depth.)
- The flexible pipe is short, so it takes up less space.
- The tank does not rust because it does not come into contact with water and has an oven-painted finish.
- Shipped with a 1-meter plug-in cable.
- A float switch is included, connected to the unit.
Baymak Jet 82-50LT Booster Pump, Horizontal Tank, 3 Floors, 4 Units
- Mechanical Seal: Carbon / Ceramic / NBR
- Impeller Material: Technopolymer
- Pump Casing: Cast Iron
- Pump Shaft: Stainless Steel
- Venturi, Diffuser: Technopolymer
- Protection Class: IP 44
- Insulation Class: F
- Max. Fluid Temperature: +40 °C
- Max. Operating Pressure Rating: 8 Bar
- Operating Pressure Range: 2–3.5 Bar
- Connection Size: 1" / 1"
- Motor Power: 0.8 HP / 0.60 kW
- Total Weight: 28 kg
- Voltage: 220 V
| A(mm) | B(mm) | C(mm) | D(mm) | E(mm) | F(mm) | H(mm) |
| 650 | 430 | 630 | 720 | 190 | 405 | 760 |
Baymak Jet 82-50LT Important Notes
- Baymak booster pump initial start-up must be carried out by an authorized Baymak service center. Otherwise, the warranty will be void.
- Transport the Baymak Jet 82-50LT only in its original packaging, following the warnings on the box.
- For Baymak Jet 82-50LT installation, it is recommended to draw suction at least 30 cm above the bottom of the tank to prevent foreign matter in the water (sand, etc.) from damaging the unit.
- The Baymak booster pump must not be connected to draw directly from the city mains; it must draw from a storage tank.
- Do not interfere with the expansion vessel valve; it is charged with compressed air when there is no water in the pump.
- The pressure switch has been factory-set; do not make any adjustments.
- It is recommended to install the Baymak booster pump in a well-ventilated location where the temperature does not exceed 40 °C.
- Install the suction and discharge pipes with clamps so that the load is transferred to the wall.
- If the Baymak Jet 82-50LT does not move after being idle, loosen the shaft at the rear of the motor.
- If the water inside the unit is to be completely drained, this must be done in an environment below 0 °C. If the unit will not be used for an extended period, draining is recommended to prevent internal corrosion.
- Install a switch proportional to the current, observing the information on the Baymak Jet 82-50LT label.
- Under no circumstances allow anyone other than authorized service personnel to work on the unit.
- For the installation piping: if metal pipe is used, the inlet/outlet diameters must be the same; if plastic pipe is used, the next size up should be selected.
- The suction line should be as short as possible (maximum 6 m) and made with the fewest possible fittings.
- Never run the Baymak Jet 82-50LT dry. Otherwise the mechanical seal, impeller, and electric motor will burn out and the warranty will be void.
- We recommend using the Baymak Jet 82-50LT with a protection panel against electrical faults.
Specifications
| Brand | Baymak |
|---|
Similar products
- Water Sound GP2624 Automatic Booster Pump, 24V, 120W, Caravan & Boat – $224.50
- Water Sound GP2612 Automatic Booster Pump, 12V, 120W, Caravan & Boat – $224.50
- Hidrotank TD 50 Vertical Pressure Tank, 50 L, 1″ Connection – $96.15
- İKRAHİDRO-11H 1 Floor 1 Apartment Booster Pump with Pressure Switch – $106.98
- Seaflo Automatic Booster Pump, 12V, 24 L Tank, Boat, Yacht & Caravan – $302.45
- Cacheng Low-Noise Automatic Mains Pressure Booster Pump, 42 L/min, 3 Bar – $250.94
- Low-Noise Booster Pump, 24V, Boat, Yacht & Caravan, 25 L/min, 2 Bar – $126.76
- Hidrotank Globe Booster Pump Kit with Connection Set, 24 L – $106.98
- Forza TGP 130 Automatic Water Booster Pump, 3.5 Bar – $83.31
- Nano Water Filter, 1 Inch – $171.69