Baymak Euroinox 50/50 M Booster Pump, 50 L Horizontal Tank, Low-Noise, 8 Floors, 8 Units

Request a quote: 0531 565 11 25. · Out of stock

Brand: Baymak · SKU: EUROINOX5050M-50LT-02030076 · Warranty: 24 months

Baymak Euroinox 50/50 M Booster Pump, 50 L Horizontal Tank, Low-Noise, 8 Floors, 8 Units

Product description

Covered by a 2-year Baymak warranty.
For warranty purposes, you must request free commissioning from Baymak.

Baymak Euroinox 50/50 M Low-Noise Domestic Booster Pump

Ideal for small apartment buildings, workplaces, detached houses, garden villas, and automatic irrigation systems. Extremely quiet and highly efficient thanks to its horizontal multistage design. More efficient, quieter, and lighter than jet-type, peripheral, or twin-stage booster pumps. Delivers high pressure and high flow rate at significantly lower power. Energy-efficient. Takes up less space than other booster types with equivalent flow rate and head. The pump section is the Italian DAB brand. The product is covered by a 2-year Baymak warranty.

When operated in the 4–6 bar range, this booster pump delivers 4 t/h of water. Since the pump casing is stainless steel, it is more hygienic than cast iron casing types. A 5 m cable level float switch is included in the package for Baymak-brand booster pumps. No separate order is required.

Uses an original DAB pump; it is a quiet packaged villa booster pump. Features a stainless steel casing. Shipped ready as a complete package.
Quiet and high-performance thanks to its horizontal multistage pump design.
Energy-efficient.
The 50 L tank does not rust, as it has no contact with water and features an oven-painted finish.
The flexible pipe is short, so it takes up less space.
Shipped with a 1-meter plug-in cable.

Baymak Euroinox 50/50 M Low-Noise Domestic Booster Pump Technical Specifications

Mechanical Seal: Carbon / Ceramic / NBR
Impeller Material: Technopolymer
Pump Casing: Stainless Steel
Pump Shaft: Stainless Steel
Venturi, Diffuser: Technopolymer
Protection Class: IP 44 (IP 55 for terminal box)
Insulation Class: F
Max. Fluid Temperature: +40 °C
Max. Operating Pressure Rating: 8 Bar
Operating Pressure Range: 3.5–5 Bar
Connection Size: 1" / 1"
Motor Power: 1.5 HP / 1.1 kW
Total Weight: 28 kg
Voltage: 220 V

hgfhdgh

A(mm)	B(mm)	C(mm)	D(mm)	E(mm)	F(mm)	H(mm)
650	430	630	720	190	405	760

Technical Data Table
Booster Pump Model	Voltage	HP	kW	Current (A)	Capacity (L/h)	Pressure Range (Bar)	Suction Connection	Discharge Connection	Tank Volume	Weight
Euroinox 50/50 M	220 V	1.36	1	6.3	3900-2150	4-6	1	1	50	36

Baymak Euroinox 50/50 M Low-Noise Domestic Booster Pump – Important Notes

Baymak booster pump initial start-up must be carried out by an authorized Baymak service center. Otherwise, the warranty will be void.
Transport the unit only in its original packaging, observing the warnings on the box.
For installation, it is recommended to draw suction at least 30 cm above the bottom of the tank to prevent foreign matter in the water (such as sand) from damaging the product.
The Baymak booster pump must not be connected to draw directly from the city mains; it must draw from a storage tank.
Do not interfere with the expansion vessel valve; it is charged with compressed air when there is no water in the pump.
The pressure switch has been factory-set; do not make any adjustments.
It is recommended to install the Baymak booster pump in a well-ventilated location where the temperature does not exceed 40 °C.
Install the suction and discharge pipes with clamps so that the load is transferred to the wall.
If it fails to move after a pause in operation, loosen the shaft at the rear of the motor.
If the water inside the unit is to be completely drained, this must be done in an environment below 0 °C. If the unit will not be used for an extended period, draining is recommended to prevent internal corrosion.
Fit a switch proportional to the current, observing the information on the label.
Under no circumstances allow anyone other than authorized service personnel to work on the unit.
For the installation piping: if metal pipe is used, the inlet/outlet diameters must be the same; if plastic pipe is used, the next size up should be selected.
The suction line should be as short as possible (maximum 6 m) and made with the fewest possible fittings.
Never operate dry. Otherwise, the mechanical seal, impeller, and electric motor will burn out and the warranty will be voided.
We recommend using a protection panel against electrical faults.

Specifications

Brand	Baymak
Motor Power	1.36 HP
Voltage	220 V (Single-Phase)
Flow Rate Range	0-5 m³/h
Head Range	51-75 m
Number of Floors	8 Floors
Floor/Apartment Capacity	5 Floors / 12 Apartments, 8 Floors / 8 Apartments
Number of Apartments	8 Apartments
Inlet	1" - 25 mm
Outlet Diameter	1" - 25 mm
Speed (rpm)	2900 rpm
Suction Lift	8 m